Optoelectronic Displays

Share us

Mazda MX-5 Miata Duratec Low Tension Piston Rings Customized E5158

E5158

Description

?
?
Piston Ring 2.0L E5158 5158, 42077 122CID DURATEC DOHC 16V FOCUS, ECOSPORT, FORD 05 - 10 87.5mm*1.2+1.2+2.5?
?
?
Product Component: ??87.5mm(STD)Hastings Pistons Rings Set
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ???SET OF RINGS FOR 4 PISTONS
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?? 1st Ring Size 1.2mm
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ???2nd Ring Size 1.2mm
? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?? Oil Ring Size 2.5mm
?
Car Application:

?

- - - -
2005 - 2008 Ford Escape 2.3L 140CID Duratec DOHC 16V |
2005 - 2010 Ford Focus 2.0L 121CID L4 DOHC 16V |
2003 - 2007 Ford Focus 2.3L 140CID Duratec DOHC 16V |
2006 - 2009 Ford Fusion 2.3L 140CID Duratec DOHC 16V |
2001 - 2010 Ford Ranger 2.3L 140CID Duratec DOHC 16V |
2004 - 2009 Mazda 3 2.0L 122CID L4 DOHC 16V |
2004 - 2009 Mazda 3 2.3L 140CID Duratec DOHC 16V |
2003 - 2008 Mazda 6 2.3L 140CID Duratec DOHC 16V |
2001 - 2008 Mazda B2300 2.3L 140CID Duratec DOHC 16V |
2006 - 2009 Mazda MX - 5 Miata 2.0L 122CID L4 DOHC 16V |
2005 - 2006 Mazda Tribute 2.3L 140CID Duratec DOHC 16V |
2008 Mazda Tribute 2.3L 40CID Duratec DOHC 16V |
2005 - 2008 Mercury Mariner 2.3L 140CID Duratec DOHC 16V |
2006 - 2009 Mercury Milan 2.3L 140CID Duratec DOHC 16V |
- - - -

? ?

What is a piston ring

?

Located between the cylinder and the piston, piston rings are necessary components that allow the engine to operate efficiently.

?

1. Piston rings maintain gas compression between the piston and the cylinder wall.


2.?Piston rings usually make necessary minimum lubricating oil film for preventing scuffing.


3. Piston rings transfer heat from the piston crown to the cylinder.


4. Piston rings prevent the piston from knocking on the cylinder wall.

?

Most automotive pistons have three rings: The top two while also controlling oil are primarily for compression sealing (compression rings); the lower ring is for controlling the supply of oil to the liner which lubricates the piston skirt and the compression rings (oil control rings). At least two piston rings are found on most piston and cylinder combination. Typical compression ring designs will have an essentially rectangular cross section or a keystone (right angled trapezoidal) cross section. The periphery will then have either a barrel profile (top compression rings) or a taper napier form (second compression rings or scraper rings). There are some taper faced top rings and on some old engines simple plain faced rings were used.

?

Lubrication of piston rings is difficult and has been a driving force to improvements in the quality of motor oil. The oil must survive high temperatures and harsh conditions with a high-speed sliding contact. Lubrication is particularly difficult as the rings have an oscillating motion rather than continuous rotation, as for a bearing journal. At the limits of piston movement, the ring stops and reverses direction. This disrupts the normal oil wedge effect of a hydrodynamic bearing, leading to pronounced wear and the formation of a & acute;step& acute; in the cylinder bore around the height of the upper ring. Noting that some sleeve valve engines suffered far less from such wear, complex designs such as a rotating cylinder liner have been considered, just to address this problem.

?

Piston Rings critical quality

?

The piston might be a fairly loose fit in the cylinder. If it were a tight fit, it would expand as it got hot and might stick tight in the cylinder. If a piston sticks (seizes) it could cause serious damage to the engine. On the other hand, if there is too much clearance between the piston and cylinder walls, much of the pressure from the burning gasoline vapour will leak past the piston (a condition known as blow-by) and into the crankcase, and the push on the piston from combustion will be much less effective in delivering power.

?

Product Description

?

Maojia Industry’s premium piston rings are manufactured from the highest quality materials and superior steel, covering the most popular applications in the global aftermarket. Maojia Industry’s piston rings are designed to meet OE standard with the perfectly match for each application.

?

Maojia Industry’s piston rings advantages

?

1. Years of OEM experience in China and overseas.

?

2. High quality material and superior steel.

?

3. Specification perfectly match different engine.

?

4. Experienced engineers and technical team.

?

5. Advanced manufacturing equipment, R&D software and test machine.

?

6. 100% tested for size and performance before shipment.

?

7. Wide range proudcts meet customers’ requirements.

?

cheap prodocuts, china suppliers,

Read More

Previous

E4978 Engine Piston Ring Set For Chevrolet Vortec Sierra Savana 4.8 5.3 L Vortec...

Previous

Countour Escape Focus Zetec Low Tension Piston Rings For Small Engines...

Ningbo Maojia International Trading Company

Head Gasket Set,Timing Chain Kit,Timing Belt Kit

Address: No. 83 Zhongyi Road, Wuxiang Industrial Park, Yinzhou District, Ningbo,
Ningbo, zhejiang
China, 315000

Tel: 86-574-88396727
Fax: 86-574-88396721

H5响应式定制设计
26种语言,SEO营销型网站


H5/响应式/营销型企业网站; 26种语言扩展;
覆盖: 英文、法语、德语、西班牙语、葡萄牙语、俄语、阿拉伯语、波斯语、日语、韩语
了解更多