New Materials

Share us

Low Temperature Cold Drawn Seamless Steel Tube With Reducer Ripple

Low Temperature Cold

Description

ASME SA333 Seamless steel pipes for low temperature service

?

Standard: ASTM A333 / ASME SA333

Steel grade: alloy steel

A 999/A 999M specification for general requirements for alloy steel pipe

- - - -
? | Grade 1 | Grade 3 | Grade 6 |
Carbon, max, % | 0.30 | 0.19 | 0.30 |
Manganese, % | 0.40-1.06 | 0.31-0.64 | 0.29-1.06 |
Phosphorous, max. % | 0.025 | 0.025 | 0.025 |
Sulfur, max, % | 0.025 | 0.025 | 0.025 |
Silicon | - | 0.18-0.37 | 0.10 min |
Nickel | - | 3.18-3.82 | - |
- - - -

Process: cold drawn seamless pipe

The tubes cover nominal (average) wall thickness.

Application: Tube for low temperature service

?

Dimensional range:

OD: 19.05-76.2mm

Any specific size is to be discussed before offer

?

The tube be 100% eddy current tested

Ultrasonic test is as option

Straightness ≤1mm/1000mm

Roughness: Ra ≤0.8

?

Mechanical properties

- - - -
? | Grade 1 | Grade 3 | Grade 6 |
Tensile strength, min, MPa | 380 | 450 | 415 |
Yield strength, min, MPa | 205 | 240 | 240 |
? | Transverse | Transverse | Transverse |
Elongation in 2 in. or 50mm, (or 4D), min, %: Basic minimum elongation for walls 5?16 in. [8 mm] and over in thickness, strip tests, and for all small sizes tested in full section | 25 | 20 | 16.5 |
When standard round 2-in. or 50-mm gage length or proportionally smaller size test specimen with the gage length equal to 4D (4 times the diameter) is used | 20 | 14 | 12 |
- - - -

?

Test
# One notched bar impact test, consisting of breaking three specimens, shall be made from each heat represented in a heat-treatment load on specimens taken from the finished pipe.
# For material heat treated in a batch-type furnace, tests shall be made on 5% of the pipe from each lot. When heat treated by the continuous process, tests shall be made on a sufficient number of pipe to constitute 5% of the lot, but in no case less than 2 pipes.
# Each length of pipe shall be subjected to the hydrostatic test or the nondestructive electric test. The type of test to be used shall be at the option of the manufacturer, unless otherwise specified in the purchase order.

?
# Nondestructive Electric Test—Nondestructive electric tests shall be in accordance with Specification A 999/A 999M, with the following addition:

If the test signals were produced by visual imperfections, the pipe may be accepted based on visual examination, provided the imperfection is less than 0.004 in. (0.1 mm) or 12? % of the specified wall thickness (whichever is greater).

?

Visual imperfections:

? ? ? Surface roughness

? ? ? Straightener marks

Cutting chips

Steel die stamps

Stop marks, or

Pipe reducer ripple

?

Tubes shall be delivered with square cut ends. The ends are free of excessive burrs.

The tubes are bundled in the waterproof plastic sheet and packed in the wooden cases

The case is most suitable for hanging by forklift.

EN10204-3.1 MTC shall be issued

EN10204-3.2 MTC is as option

?

?







?

?

cheap prodocuts, china suppliers,

Read More

Previous

OD 19.05-76.2mm Cold drawn Low Temperature Carbon Steel Pipe ASTM SA333...

Previous

Cold drawn welded Low Temperature Carbon Steel Pipe ASTM SA333...

Zhangjiagang Bonded Area Henglong Steel Tube Company

Precision Steel Tubing,Heat Exchanger Tubes,Mechanical Steel Tubing

Address: No.5, Taiwan Road, Zhangjiagang Bonded Area, Zhangjiagang City, Jiangsu Province, China,
Zhangjiagang, Jiangsu
China, 215600

Tel: 86-512-58328328
Fax: 86-512-58328332

H5响应式定制设计
26种语言,SEO营销型网站


H5/响应式/营销型企业网站; 26种语言扩展;
覆盖: 英文、法语、德语、西班牙语、葡萄牙语、俄语、阿拉伯语、波斯语、日语、韩语
了解更多